Land Survey Company for Commercial Sign Placement Plans
Posted on by Fort Lauderdale Surveyor
That’s why many owners bring in a land survey company before the sign contractor digs. The survey gives the sign designer, engineer, and permit reviewer the same measured facts about the property. This article covers what to check at each step so your sign gets approved, built, and left alone.
A new monument sign is one of the most visible things a business will build. It’s also one of the easiest to put in the wrong spot. A few feet can decide whether the sign sits on your land, inside a utility easement, or in the public right-of-way, and moving a set foundation is expensive.
Establishing Property Boundaries Before Commercial Sign Installation
Every sign plan starts with knowing exactly where your property ends. On many commercial sites, the front property line sits well behind the curb, and the strip in between belongs to the road authority. Owners often assume the grass up to the sidewalk is theirs. A boundary survey settles that by locating corners and lines from recorded documents and field evidence.
Shared driveways and outparcels make this harder. A pylon sign serving several tenants may need to sit on one parcel while advertising businesses on another. In that case, the location should match any recorded sign or access agreements between the owners.
Ask the surveyor to mark the property line on the ground near the planned sign area. Visible stakes help the sign crew avoid guessing. They also make it easier to spot a conflict before the design is final.
Checking Easements and Setback Requirements for Sign Locations
Easements and setbacks often limit sign placement more than the boundary does. An easement is a recorded right for someone else to use part of your land, such as a utility company running lines along the frontage. Many easements restrict permanent structures, and a sign foundation is permanent. The survey can show recorded easements found in the title documents so you can keep the sign clear.
Setbacks are minimum distances a structure must sit from property lines or roads. Sign setbacks can differ from building setbacks, and they vary by municipality, county, zoning district, and sign type. Some codes also limit signs near driveways and intersections so drivers can see oncoming traffic.
The surveyor plots the lines, but the local sign code sets the rules. Get a copy of the sign regulations for your zoning district early. Then compare them against the survey so you know your allowable sign area before you order fabrication.
Assessing Site Elevations and Visibility Along Commercial Frontages
A sign that meets every rule can still be hard to see. If the sign area sits lower than the road, or a berm or landscaping rises between them, the message can disappear for passing drivers. A topographic survey measures ground elevations and existing features so you can judge how the sign will read from the street.
Use the elevation data to answer a few practical questions:
- How the sign base compares with the road surface
- Whether trees, walls, or nearby structures block sightlines
- Where grade changes might affect drainage around the foundation
- How sign height limits apply on your site, since codes define the starting point differently
Drainage matters more than most owners expect. A sign placed in a low spot can collect standing water around its base. Moving it a short distance to higher ground can protect the foundation and the landscaping around it.
Using Survey Data to Coordinate Sign Foundations and Utility Clearances
Sign foundations go deeper than most people picture, and commercial frontages are crowded underground. Water, sewer, gas, power, and communication lines often run along the road edge. A land survey company can show visible utility features like manholes, valves, poles, and boxes, and it can map marked underground lines when those locates are part of the scope.
Always call 811 before any digging, even with a survey in hand. The 811 locate marks public utility lines in the dig area, but private lines may need a private locator. Overhead power lines matter too, because signs and the equipment used to set them need safe clearance.
Give the survey to the engineer designing the sign foundation. The engineer can place the footing around utilities and easements while meeting the structural needs of the sign. Fixing a conflict on paper costs far less than fixing it after the concrete cures.
Preparing Accurate Site Plans for Sign Permits and Construction
Most sign permits ask for a site plan showing where the sign will go. Reviewers usually want distances from property lines, nearby structures, driveways, and the right-of-way. Requirements vary by municipality and county, so confirm the exact checklist with the permit office before the plan is drawn. A plan built on survey data is much less likely to come back with corrections.
Once the permit is approved, the surveyor can stake the sign location on site. Staking means setting marks that show the contractor exactly where the foundation goes. Some owners also ask for a quick check after the foundation is set, which confirms the sign landed where the approved plan says.
Plan the survey early if your opening date depends on the sign. Permit review takes time, and a rejected plan can push installation back. Ordering survey work at the start keeps the schedule in your hands.
Frequently Asked Questions
Do I need a survey to get a commercial sign permit?
It depends on your municipality and the type of sign. Many permit offices ask for a site plan with measured distances to property lines and the right-of-way. A survey is often the most reliable way to produce those measurements. Check with your local permit office early so you know what they’ll accept.
Can a sign be placed inside a utility easement?
Many easements limit or prohibit permanent structures, and a sign foundation usually counts as one. The answer depends on the easement’s wording and the holder’s rules. Some owners get written permission, but that isn’t guaranteed. Have the survey show the easement and ask your attorney or title company to review the language.
What happens if my sign ends up in the right-of-way?
The road authority may require you to remove or move it, and you may carry the cost. Signs in the right-of-way can also block driver sightlines or get in the way of road work. A boundary survey shows where your property line actually sits before the foundation goes in. That check is far cheaper than relocating a finished sign.
For a free land surveying quote, call us at (954) 250-5780 or send us a message by going here.
Posted in land surveying | Tagged land surveying
